specifications subject to change without notice. all dimensions in inches. ? copyright 2008 the connor-winfield corporation 2111 comprehensive drive aurora, illinois 60505 phone: 630- 851- 4722 fax: 630- 851- 5040 www.conwin.com bulletin tx214 page 1of4 revision 01 date 05 sep 2008 us headquarters: 630-851-4722 european headquarters: +353-61-472221 description package layout features: pad connections example part number ordering information m602 - 012.8m tcxo series center frequency precision sub-miniature 5.0x3.2mm tcxo / vctcxo applications gps receivers instrumentation femtocells ftth, fttc the connor-winfield 5.0x3.2mm temperature compensated crystal oscillators and voltage controlled temperature compensated crystal oscillators are designed for use in applications requiring tight frequency stability in a small package. through the use of analog temperature compensation, this device is capable of holding sub 1-ppm stabilities over wide temperature ranges. 3.3v operation lvcmos or clipped sinewave output logic sub-miniature 5.0x3.2mm smt package frequency stabilities available: 0ppm or . 0ppm temperature ranges available: 0to70c - 0 to c low power <10ma low jitter <1ps rms tape and reel packaging rohs compliant / lead free recommended for new designs 0.28ppm with stratum 3 holdover, 0.5 1 0 485 pad connection 1 voltage control or n/c 2 do not connect 3 do not connect 4 ground 5 output 6 do not connect 7 do not connect 8 supply, vcc ordering information 2 type: precision tcxo vctcxo 3.2x5mm features: 2= 4=vc 5= vc tcxo, lvcmos, 3.3vdc. 3 = tcxo, clipped sinewave, 3.3vdc. tcxo, lvcmos, 3.3vdc. tcxo, clipped sinewave, 3.3vdc. temperature range: 5=0to 6 = -40 to 85 70 c c frequency stability: 2= 0= 1= 0.28 ppm 0.50 ppm 1.00 ppm m 6 0 012.8m - 0.126 (3.2mm) 0.197 (5.0mm) 0.083 max. (2.1mm) m602 0806 12.8mhz 0.050 (1.27mm) 0.016 (0.41mm) 0.042 (1.07mm) 0.008 typ. (0.20mm) 0.006 typ. (0.15mm) 0.028 (0.71mm) 0.042 (1.07mm) 0.065 (1.65mm) 0.028 (0.71mm) to p view bottom view pad 1 pad 8 dimensional tolerance: +/-0.005 (+/-0.127mm) output frequency: frequency format -xxx.xm min.* -xxx.xxxxxxm max.* *amount of numbers after the decimal point. m = mhz example: m602-012.8m = 3.2x5mm, tcxo, lvcmos, 3.3vdc, -40 to 85c, +/-0.28ppm, output frequency 12.8mhz to order an m602 with an output frequency of: 6.4 mhz = m602-006.4m 20 mhz = m602-020.0m 38.88 mhz = m602-038.88m stratum 3 applications m602 0806 12.8 mhz designed for telecom applications consult the factory for available frequencies.
2111 comprehensive drive aurora, illinois 60505 phone: 630-851-4722 fax: 630-851-5040 www.conwin.com us headquarters: 630-851-4722 european headquarters: +353-61-472221 bulletin page revision date tx214 2of4 01 05 sep 2008 model specifications specifications subject to change without notice. all dimensions in inches. ? copyright 2008 the connor-winfield corporation features lvcmos test circuit 4 5 2 3 6 7 8 1 vcc supply voltage n/c - tcxo vc - vctcxo dnc dnc dnc .01 uf bypass output 15 pf* dnc clipped sinewave test circuit 4 5 2 3 6 7 8 1 vcc supply voltage n/c - tcxo vc - vctcxo dnc dnc dnc .01 uf bypass output 10 pf* 10kohm dnc ac coupling capacitor dnc = do not connect * npo grade component dnc = do not connect * npo grade component m602 0806 12.8 mhz 3.3v operation lvcmos or clipped sinewave output logic sub-miniature 3.2x5.0mm smt package frequency stabilities available: 0ppm or . 0ppm temperature ranges available: 0to70c low power <10ma low jitter <1ps rms tape and reel packaging rohs compliant / lead free recommended for new designs 0.28ppm with stratum 3 holdover, 0.5 1 0 -40 to 85 c model number m502 m503 m504 m505 notes output type lvcmos clipped sinewave lvcmos clipped sinewave tcxo / vctcxo tcxo tcxo vctcxo vctcxo frequency range 6.4 to 40 mhz frequency stability 0.28ppm 1 supply voltage 3.3vdc temperature range 0 to 70c holdover stability 0.32ppm 2 model number m602 m603 m604 m605 notes output type lvcmos clipped sinewave lvcmos clipped sinewave tcxo / vctcxo tcxo tcxo vctcxo vctcxo frequency range 6.4 to 40 mhz frequency stability 0.28ppm 1 supply voltage 3.3vdc temperature range -40 to 85c holdover stability 0.32ppm 2 model number m512 m513 m514 m515 notes output type lvcmos clipped sinewave lvcmos clipped sinewave tcxo / vctcxo tcxo tcxo vctcxo vctcxo frequency range 6.4 to 40 mhz frequency stability 0.50ppm 1 supply voltage 3.3vdc temperature range 0 to 70c model number m612 m613 m614 m615 notes output type lvcmos clipped sinewave lvcmos clipped sinewave tcxo / vctcxo tcxo tcxo vctcxo vctcxo frequency range 6.4 to 40 mhz frequency stability 0.50ppm 1 supply voltage 3.3vdc temperature range -40 to 85c model number m522 m523 m524 m525 notes output type lvcmos clipped sinewave lvcmos clipped sinewave tcxo / vctcxo tcxo tcxo vctcxo vctcxo frequencyrange 6.4to52mhz frequency stability 1.00ppm 1 supply voltage 3.3vdc temperature range 0 to 70c model number m622 m623 m624 m625 notes output type lvcmos clipped sinewave lvcmos clipped sinewave tcxo / vctcxo tcxo tcxo vctcxo vctcxo frequencyrange 6.4to52mhz frequency stability 1.00ppm 1 supply voltage 3.3vdc temperature range -40 to 85c notes: 1) frequency stability vs. change in temperature. [(fmax ? fmin)/2.fo]. 2) inclusive of frequency stability, supply voltage change (1%), aging, for 24 hours.
2111 comprehensive drive aurora, illinois 60505 phone: 630-851-4722 fax: 630-851-5040 www.conwin.com us headquarters: 630-851-4722 european headquarters: +353-61-472221 bulletin page revision date tx214 3of4 01 05 sep 2008 electrical specifications for all models specifications subject to change without notice. all dimensions in inches. ? copyright 2008 the connor-winfield corporation features lvcmos test circuit 4 5 2 3 6 7 8 1 vcc supply voltage n/c - tcxo vc - vctcxo dnc dnc dnc .01 uf bypass output 15 pf* dnc clipped sinewave test circuit 4 5 2 3 6 7 8 1 vcc supply voltage n/c - tcxo vc - vctcxo dnc dnc dnc .01 uf bypass output 10 pf* 10kohm dnc ac coupling capacitor dnc = do not connect * npo grade component dnc = do not connect * npo grade component m602 0806 12.8 mhz 3.3v operation lvcmos or clipped sinewave output logic sub-miniature 3.2x5.0mm smt package frequency stabilities available: 0ppm or . 0ppm temperature ranges available: 0to70c low power <10ma low jitter <1ps rms tape and reel packaging rohs compliant / lead free recommended for new designs 0.28ppm with stratum 3 holdover, 0.5 1 0 -40 to 85 c absolute maximum ratings parameter units minimum nominal maximum units note storage temperature -55 - 85 c supply voltage (vcc) -0.5 - 6.0 vdc input voltage (vc) -0.5 - vcc+0.5 vdc operating specifications parameter minimum nominal maximum units notes tcxo frequency calibration @ 25 c -1.00 - 1.00 ppm 1 supply voltage variation. (vcc5%) -0.2 - 0.2 ppm load coefficient, 5% -0.2 - 0.2 ppm static temperature hysteresis -0.4 - 0.4 ppm 2 total frequency tolerance -4.60 - 4.60 ppm 3 supply voltage (vcc) 3.135 3.3 3.465 vdc 4 supply current (icc) - 6 10 ma period jitter - 3 5 ps rms integrated phase jitter (bw=12khz to 20mhz) - 0.3 1.0 ps rms ssb phase noise at 10hz offset - -80 -70 dbc/hz ssb phase noise at 100hz offset - -110 -100 dbc/hz ssb phase noise at 1khz offset - -135 -130 dbc/hz ssb phase noise at >10khz offset - -150 -145 dbc/hz ssb phase noise at >100khz offset - -150 -150 dbc/hz start up time - - 10 ms input characteristics for voltage control (pad 1) parameter minimum nominal maximum units notes control voltage range (vcc = 3.3v) (vc) 0.3 1.65 3.0 vdc frequency tuning 10 - - ppm 5 linearity 5 - - % slope positive lvcmos output characteristics parameter minimum nominal maximum units notes load - 15 - pf 6 voltage (high) (voh) 90%vcc - - vdc (low) (vol) - - 10%vcc vdc current (high) (ioh) -4 - - ma (low) (iol) - - 4 ma duty cycle at 50% of vcc 45 50 55 % rise / fall time 10% to 90% - - 8 ns clipped sinewave output characteristics parameter minimum nominal maximum units notes load - - - 7 output load resistance - 10k - ohms 8 output load capacitance - 10 - pf 8 output voltage 1.00 - - v pk-pk 1) tcxo: initial calibration @ 25 c. specifications at time of shipment after 48 hours of operation. 2) frequency change after reciprocal temperature ramped over the operating range. frequency measured before and after at 25c. 3) inclusive of calibration @ 25 c, frequency vs. change in temperature, change in supply voltage (5%), load change (5%), reflow soldering process and 20 years aging. 4) for best in application performance, careful selection of an external power source is critical. select an external regulator that meets or xceeds to following specifications regarding voltage regulation tolerance, initial accuracy, temperature coefficient, voltage noise, and low voltage noise density. factory test conditions: initial accuracy 2mv, noise (0.1hz to 10 khz) 15uv p-p, voltage noise density = 50nv/(square root hz), temperature coefficient < 5ppmc. 5) additional pull ranges are available; please contact the factory for additional information. 6) for best performance it is recommended that the device connected to this output should have an equivalent input capacitance of 15pf. 7) output is dc coupled. 8) for best performance it is recommended that the device connected to this output should have an equivalent input capacitance of 10pf. notes
2111 comprehensive drive aurora, illinois 60505 phone: 630-851-4722 fax: 630-851-5040 www.conwin.com us headquarters: 630-851-4722 european headquarters: +353-61-472221 bulletin page revision date tx214 4of4 01 05 sep 2008 specifications subject to change without notice. all dimensions in inches. ? copyright 2008 the connor-winfield corporation 120c 150c 180c 260c 0 220c 360 sec. max. 120 s max. 10 s 60 s max. time temperature 260c model m602-012.8mhz typical phase noise solder profile suggested pad layout tape and reel specifications clipped sinewave output waveform lvcmos output waveform 90% 50% 10% environmental characteristics vibration: vibration per mil std 883e method 2007.3 test condition a shock: mechanical shock per mil std 883e method 2002.4 test condition b. soldering: smd product suitable for convection reflow soldering. peak temperature 260 c. maximum time above 220 c, 60 seconds. solderability solderability per mil std 883e method 2003 dimensional tolerance: +/-0.005 (+/-0.127mm) 0.028 (0.71mm) 0.053 (1.35mm) 0.098 (2.49mm) 0.050 (1.27mm) 0.050 (1.27mm) to p view external ac coupling capacitor used for clipped sinwave output 1 4 5 8 external bypass capacitor 0.01 uf to ground to output keep out area* to cmos output * do not route any traces in the keep out area. it is recommended the next layer under the keep out area is to be ground plane. 10ns 200mv
|
